V-Mod Version 2 900mAh Variable Voltage 510-threaded Battery



**No cartridge included with this battery.

Vapmod products are designed in California and are then manufactured in China (Sunzip Group). They pride themselves on providing a high level of quality with each of the products they create. Sunzip has a goal of bringing their customers a safe, efficient and good looking device via intensive in-house research and development.

Cartridge vaping has boomed in Australia in the past year. I have witnessed this firsthand in store whereby a year ago I sold almost no cartridges (empty, of course!) and only a small amount of battery sticks/mods specifically designed for cartridge vaping. For those of you who are unaware, cartridges are used for thick oil (usually herbal). These oils are dense and quite resinous and will not vape efficiently in standard vaporisers that are designed to vape e liquids.


The V2 is the upgraded version of the first V-mod with one main difference between both, the V2 has haptic feedback included. Haptic feedback is a fancy term to describe vibration as an alert system.

Just like the first model the V-mod 2 is a petite little device, relatively flat, square and minimalistic (reminds me of an i-pod). If discretion is your thing then you will love this mod as it can easily be held entirely within the palm of your hand and into your pocket. A cartridge (not included) will sit partly within the square with only a small section exposed (mouthpiece). Different lengths of cartridges will peek out at various heights – hole depth is 37mm. A side window on  the side of the battery allows you to view the interior of your cartridge.

TIP: As cartridges sit inside the mod it is important to ensure that the diameter of your cartridge isn’t too wide for insertion. Diameter = 11.5mm.

Pay attention – this part is important. Cartridges are held in place via an included magnetic 510 connector that attaches to the base of each cartridge used. This magnet will keep the cartridge in place enabling easy removal/insertion when needed. Your cartridge will not stay in place without the adapter.

TIP: I would recommend keeping track of your used cartridges and checking before disposal, so you don’t accidentally throw out the magnetic connector!

The V-mod has quite an impressive battery capacity – 900mAh. This is a lot and according to Vapmod will last up to 600 puffs before a recharge will be required. I personally have not tested this assertion but find it to be believable as I currently use a much lower capacity battery (380mAh) and only charge once a week or so. The V-mod 2 has a preheat function and will allow you to modify your voltage with 3 levels offered. Each colour also corresponds to remaining battery life.

Colour Voltage Battery Capacity
Green Light 2.6V 70%+
Yellow Light 3.2V 30 – 70%
Red Light 4.0V Less than 30%

I love safety, especially whilst vaping. The V-mod 2 comes complete with a myriad of safety features allowing you to vape without worrying. The following come standard:

  • Overcharge protection
  • Over-voltage protection
  • Over-current protection
  • Over discharge protection
  • Short circuit protection


Ensure your V-mod 2 is charged. Attach the magnetic connector to the base of the cartridge being used. You can then easily insert your cartridge and it will be held in place. X5 clicks will turn your battery on (same for off). The light will flash twice when turned on and only once when turned off. Once your mod is on x3 clicks will allow you to cycle through the 3 pre-set voltages. See above table for corresponding colour light.

TIP: If your oil becomes thick/gluggy or has become cold you may want to utilise the preheat function. X2 clicks will begin the process (light will “breathe”) and will continue for 15 seconds or until you click once to end it.


  • x1 Vmod 2 900 mAh Battery
  • x1 510-Threaded Magnet Connector Ring
  • x1 USB Cable
  • x1 Warranty Card
  • x1 User Guide.


  • Battery capacity: 900mAh
  • Haptic Feedback
  • Uses: Concentrates/thick herbal oils
  • Micro USB
  • 3 Voltage settings
  • Magnetic connector
  • Length: 49mm
  • Width: 49mm
  • Height: 14mm
  • Weight: 85g
  • Hole depth: 37mm
  • Hole diameter: 11.5mm
  • Output voltage: 2.6 – 4.1v
  • Preheat output: 1.8v
  • Preheat time: 15 seconds
  • Puffs per charge: 600

Black, Red

  • No products in the cart.